Can I manually set the IP address on my device?

IMPORTANT: This article applies only to specific products and/or operating systems. Check Applicable Products and Categories for details.

Many devices support entering the IP address manually. This information is provided to help guide you through the manual steps used for most devices. If it's not necessary to enter your IP address manually, it's recommended to use the easy setup.

Before you start

• Because your Internet Service Provider (ISP) may have specific Gateway or DNS requirements or restrictions, we recommend that you contact them before attempting to set a manual IP address.
• You should have a good understanding of your network and the settings of your router, and be able to obtain the necessary information from your computer to manually set the IP address of your device.
• The design and settings of your router determine the steps to set up the IP address and proxy server settings on your device. If the router has not automatically assigned an IP address to the device, you may be able to set the IP address manually.
• Some models don't support manually setting the IP address when using the wireless connection option.

Manually set the IP address of your device

1. Obtain the following IP information from your computer.
   Note: If your device is already connected to the internet, the IP information may also be obtained from the network connection status of the device.
   • IP address or IPv4 address
   • Subnet Mask (not required on all devices)
   • Default Gateway
2. Enter the IP information in the network settings of your device.
   Note: The steps to change the network settings of your device may vary depending on the model. Check the manual for model-specific information.
   Manuals are posted on your model support page.
   • Android TV™ models

     1. Access the Settings screen.
        • Using the Quick Settings button (For models released in 2019 or later)
          1. On the remote control, press the (Quick Settings) button.
          2. Select Settings.
        • Using the HOME button
          1. On the remote control, press the HOME button.
          2. Select Settings.
     2. The next steps depend on your TV menu options:
        • Select Network & Internet.
        • Select Network → Network setup → Expert.
     3. Navigate to your network connection type (Wired LAN or Wi-Fi®). If you're using Wi-Fi, make sure you select the name of your connected Wi-Fi network.
     4. For older models before Android 7 Nougat (N) OS, select Advanced options.
     5. Select IP settings.
     6. Select Static.
     7. Enter the IP information obtained from your computer.
        • IP address: The IP address should be the same, except for the last number in the four-number sequence. Change the last number to a number higher than the original, but less than 254. For example, if the IP address shown on your computer is 192.168.0.5, enter 192.168.0.105
        • Subnet Mask: If this setting is listed, enter the Subnet mask exactly as attained from the computer.
        • Gateway: Enter your gateway address exactly as attained from the computer.
        • Network prefix length: If this setting is listed, in most cases, 24 is appropriate.
        • DNS 1 (primary DNS): Enter the desired IP address of your first DNS server (example 8.8.8.8).
        • DNS 2 (secondary DNS): Enter the desired IP address of your second DNS server (example 8.8.4.4).
        • If prompted to use a proxy server, select NO.

   • Other TV models

     1. Press the HOME button.
     2. Select Settings.
     3. Select System Settings.
     4. Select Set-up.
     5. Select Network.
     6. Select Network Set-up.
     7. Under the Network Set-up category, select Set up network connection.
     8. Select Expert.
     9. Select Wired Set-up.
     10. Select Manual.
     11. Enter the IP information obtained from your computer.
         • IP address: The IP address should be the same, except for the last number in the four-number sequence. Change the last number to a number higher than the original, but less than 254. For example, if the IP address shown on your computer is 192.168.0.5, enter 192.168.0.105
         • Subnet Mask: Enter the Subnet mask exactly as attained from the computer.
         • Default Gateway: Enter the Default Gateway exactly as attained from the computer.
         • Primary DNS: Enter the desired IP address of your first DNS server (example 8.8.8.8).
         • Secondary DNS: Enter the desired IP address of your second DNS server (example 8.8.4.4).
         • If prompted to use a proxy server, select NO.
     12. Select Save and Connect to establish a network connection.

   • Other internet devices

     1. Press the HOME or MENU button.
     2. Select Setup or Settings.
     3. Select Network.
     4. Select Network Setup.
     5. Depending on how the device is connected to your network, select either Wired or Wireless.
     6. Select Manual or Custom.
        • If these options are not available, an IP address cannot be manually set on your model.
        • For a secured wireless setup, enter a Network security key to display the IP address and Proxy server setting screen.
     7. Enter the IP information obtained from your computer.
        • IP address: The IP address should be the same, except for the last number in the four-number sequence. Change the last number to a number higher than the original, but less than 254. For example, if the IP address shown on your computer is 192.168.0.5, enter 192.168.0.105
        • Subnet Mask: Enter the Subnet mask exactly as attained from the computer.
        • Default Gateway: Enter the Default Gateway exactly as attained from the computer.
        • Primary DNS: Enter the desired IP address of your first DNS server (example 8.8.8.8).
        • Secondary DNS: Enter the desired IP address of your second DNS server (example 8.8.4.4).
        • If prompted to use a proxy server, select NO.
     8. Select Save and Connect to establish a network connection.