SEL50F14Z System Software Update (Mac)

WAIT - Read the Required Files section before downloading this file.

Required Downloads

Unless stated otherwise, the file listed below must be installed BEFORE the SEL50F14Z System Software Update (Mac) in order for it to work properly. If more than one Required file is listed, install them in the order presented on this page.

System Software Update Helper

IMPORTANT: This file is only for use with the models identified. Not all models are sold in all countries.

This information is for the following models:

ILCE-9
SEL50F14Z

About this download

Benefits and improvements

This utility updates the lens system software to version 02 and provides the following changes and benefits:

Adds supports for continuous, blackout free shooting of up to 20 frames per second when using the ILCE-9
Improves the autofocus tracking performance

Notes: This Lens system software update is available for the E-mount body.

Some models cannot be used for this update. (model list)
When using PXW-FS7M2, please follow the procedure according to the instruction manual of PXW-FS7M2.

System Requirements

Operating Systems

Mac OS® X

File Info

File Name

Update_SEL50F14ZV2D.dmg

File Version

File Size

1.77 MB

Release Date

05-24-2017

Before You Start

Determine if you need this update

Check the version of your camera lens System Software:

Attach the lens to the camera.
Note: Please make sure the camera is off before you attach the lens.
Power on the camera.
Press the Menu button.
At the Menu screen, select Setup.
At the Setup screen, select Version.
The System Software version is displayed on the LCD screen.

Note: If the current System Software version is Ver.02 or higher, the camera lens doesn't need this update.

Before You Start

This System Software update can be performed only when the lens is attached to a camera. Don't install this update with any other model.
WARNING! This System Software update and any changes incurred by it are permanent. It's not possible to return to a previous version after updating this System Software. By continuing this update process and downloading and updating this System Software, you acknowledge that you are aware and understand that this update can't be reversed.
This update process requires the following items for proper updating:
- A computer with:
  - CPU: Intel® processor
    Note: Core™ Solo and Core Duo processors are not supported.
  - Available Hard Disk Space: 200 MB or more
  - Installed Memory (RAM): 512 MB or more
  - A USB port.
  - Apple® Mac OS X® version 10.10 - 10.13
- This Lens system software update is available for the E-mount body.
  - Some models cannot be used for this update. (model list)
  Note: Camera models NEX-5R and NEX-6 require firmware version 1.01 or higher, for the latest camera firmware information, please visit the NEX-5R or NEX-6 support page.
- A USB cable: Use only the USB cable supplied with the camera.
  Note: Update functionality isn't guaranteed with any other USB cable.
This update can only be performed when the remaining battery level has three bars or more. It's recommended that you use a fully charged NP-FW50 rechargeable battery pack, or the AC-PW20 AC adapter/charger (sold separately).
WARNING! Don't remove the battery pack or AC adapter during the update process, otherwise, the camera may become inoperable due to the sudden power loss.
To keep other programs from interfering with the installation, save all work and close all other programs before proceeding.

Download & Install

Installation Instructions

Download the Update_SEL50F14ZV2D.dmg file to a directory on your computer, and make note of this directory for reference.
Go to the directory where the file was downloaded and double-click the Update_SEL70200GMV2D.exe file to begin the Lens System Software Updater.
At the Password prompt screen, enter the Name and Password for the administrative account, and then click OK.
Remove the memory card from the camera
Make sure the lens is attached the camera.
Note: Make sure the camera is off before you attach the lens.
Power on the camera.
Note: If the camera has already been powered on, power it off and then back on again.
On the camera, press the Menu button, select Setup, and then USB Connection and make sure Mass Storage is selected (this step isn't necessary if you are using a QX series camera).
Connect the camera to your computer using the supplied USB cable.
On the computer, the Lens System Software Updater window appears, and on the camera, the screen displays the message Follow computer instructions.
Notes:
- If the message The update isn't available for your model appears on the screen, make sure the System Software update is the correct file for the lens you have attached. If the file is correct for the lens, close the Firmware Updater program, disconnect the USB cable, power off the camera, restart the Lens System Software Updater program, and then continue the procedure.
- If the message Could not find the camera with the lens for this update mounted appears on the screen, make sure you are using a a camera with the Fast Hybrid AF function, try disconnecting and reconnection the USB cable, and try another USB port on the computer.
At the Lens System Software Updater window, click Next.

WARNING! Don't power off the camera or disconnect the USB cable until the update process is complete.
When the following screen is displayed, check the version number at the lower left.

Note: If the current version is Ver.02, your camera lens doesn't need this update. Stop the USB connection, click the Finish button on the Lens System Software Updater screen, power off the camera, briefly remove the battery pack or the AC adaptor, and then power on the camera again.
If the current version is Ver.01, click Next.
The lens system software transfer will start and a progress bar will be displayed showing the data transfer.
Note: This part of the process takes about five minutes to complete.
When the data transfer is complete, the following screen is displayed, click Finish.
The update process starts and the progress bar is displayed on the camera screen.
The update process is finished when the Lens update complete message is displayed on the camera screen.
Stop the USB connection, disconnect the USB cable, power off the camera, and then remove the battery pack or AC adapter.
Reconnect the battery pack or AC adapter and power on the camera.
Check the current firmware version to confirm that the update has successfully installed.
- If the version is Ver.02, the firmware update was successful.
- If the version is not Ver.02, download and install the update again.